[Linux-HA] HB 2.0.7 installation&compilation errors

[Nikita Michalko]

Am Donnerstag, 5. Oktober 2006 04:04 schrieb Alan Robertson:
> Andrew Beekhof wrote:
> > On 9/25/06, Nikita Michalko <aipadmin at aip.xss.co.at> wrote:
> >> Am Montag, 25. September 2006 09:08 schrieb Andrew Beekhof:
> >> > On 9/25/06, Nikita Michalko <aipadmin at aip.xss.co.at> wrote:
> >> > > Am Sonntag, 24. September 2006 15:19 schrieb Andrew Beekhof:
> >> > > > On 9/22/06, Nikita Michalko <aipadmin at aip.xss.co.at> wrote:
> >> > > > > Hi list !
> >> > > > >
> >> > > > > I  have installed SLES 10 and all necessary RPM's for HB 2.0.7 (
> >> > > > > 64-bit box). After uninstall of HB 2.0.5 - which was
> >> > > > > preinstalled already /default - and trying to install V2.0.7
> >> > > > > from tarball
> >>
> >> (with
> >>
> >> > > > > 'ConfigureMe rpm' ), I get following errors:
> >> > > > > ...
> >> > > > > cat: /etc/ld.so.conf.d/*.conf: No such file or directory
> >> > > > > ...
> >> > > > > --- snip --
> >> > > > > + make:
> >> > > > > libtool: link: warning:
> >>
> >> `/usr/lib64/gcc/x86_64-suse-linux/4.1.0/../../../../lib64//libbz2.la'
> >>
> >> > > > > seems to be moved
> >> > > > > libtool: link: warning:
> >>
> >> `/usr/lib64/gcc/x86_64-suse-linux/4.1.0/../../../../lib64//libxml2.la
> >>
> >> > > > >' seems to be moved
> >> > > > > libtool: link: warning:
> >>
> >> `/usr/lib64/gcc/x86_64-suse-linux/4.1.0/../../../../lib64//libltdl.la
> >>
> >> > > > >' seems to be moved
> >> > > > > gcc: -lpthread: linker input file unused because linking not
> >> > > > > done --- snip --
> >> > > > > libtool: install: warning: remember to run `libtool --finish
> >> > > > > /usr/lib64' libtool: install: warning: remember to run `libtool
> >> > > > > --finish /usr/lib64/heartbeat/plugins/test'
> >> > > > > libtool: install: warning: relinking `libstonith.la'
> >> > > > > --- snip --
> >> > > > > The shared libraries are also in the directory /lib64 , not only
> >> > > > > in /usr/lib64. Is that OK ?
> >> > > > >
> >> > > > > Thanks  for any hints !
> >> > > >
> >> > > > Does compilation complete?  Both of those things are usually
> >>
> >> ignorable.
> >>
> >> > > Thank you for response, Andrew. Yes, compilation did complete -
> >>
> >> there are
> >>
> >> > > RPM's there.
> >> >
> >> > In that case I'd try installing them and running BasicSanityCheck to
> >> > verify everything is ok (it should be fine).
> >>
> >> Hi Andrew,
> >>
> >>  after installing V2.0.7 and running BasicSanityCheck I've got 13
> >> errors - see
> >> log file AIP_linux-ha.testlog attached:
> >> ...
> >> -OOPS! Looks like we had some errors come up.
> >> -13 errors. Log file is stored in /tmp/linux-ha.testlog
> >> It complains about :
> >> "mcast device [1.1.1.19] is invalid or not set up properly" - but I
> >> don't understand why.
>
> 1.1.1.19 isn't an mcast address...  So, I don't think I've ever seen
> that error.  Could you send me the entire log?  I'm way behind on this
> mailing list.
>
Thank you for your time, Alan !
In the meantime I've already removed the original log - sorry for that :-(
But after installing HB 2.0.7 on the new SLES10 box it works - does it mean,
I MUST use  mcast address (in config file)  to run BasicSanityCheck without 
errors ?

Nikita Michalko

> >> ifconfig shows interface eth0 with IP 1.1.1.19 (node "castor")  UP and
> >> RUNNING, ping and telnet to this IP address is OK.
> >> What's the matter - what's wrong ?
> >
> > not sure.  something at the communications layer.  alan?